Skip to content

The open beta runs until 30 November. From 1 December Volter is paid, and accounts created before 1 December stay free until 31 December. See the prices

Dictating and processing notes

Dictate a site note or type it, let the assistant put it on the plan and check its proposal before you accept it.

Dictating or typing a note

Notes belong to the project. Anyone can type, dictating needs Volter AI.

  1. Click the round Notes button at the bottom right of the drawing sheet.
  2. Type your note, or click the Dictate a note microphone and speak.
  3. Click Stop recording when you are done. A recording lasts at most two minutes. Volter counts down the last fifteen seconds.
  4. The recognised text goes into the field, not into the list yet. Read it through and correct what was misheard.
  5. Click Save.

The note gets the floor that is open, and the word spoken if you dictated it. Volter understands you in the language of the app. The names of your rooms, floors and circuits go along with the recording, so they are spelled correctly.

Click the text of a note to edit it. With the box in front of it you tick it off.

Having a note put on the plan

  1. Open Notes and click Process into the plan below the note.
  2. Volter opens the floor plan of the floor of the note and the Assistant window. The note is now your question.
  3. The assistant answers with a Proposal card. Read it through, see Checking a proposal.
  4. After Accept the assistant asks whether you want to tick off the note. Choose Tick off or Not now.

The assistant never ticks off by itself. A proposal does not always cover the whole note.

You can also work without a note. In the Assistant window, type or say what should go on the plan, for example: put a socket outlet to the left of the door in the kitchen.

Checking a proposal

A proposal shows in two places: as a card below the answer, and dotted on the plan. The numbers on the card are also next to the symbols on the plan.

The assistant can propose to:

  • place new symbols in a room: in the middle, against a wall, or to the left or right of a door or window
  • put existing symbols in a room on another circuit
  • delete existing symbols in a room
  • change values of a circuit, such as the amperage, the curve or the wire size

This is how you check it:

  1. Read every step: what, in which room, in which spot and on which circuit.
  2. For a new symbol you choose the circuit in the Choose a circuit list. You can do that even if the assistant already chose one.
  3. If a step shows a reason instead of a circuit, that step cannot be done. The other steps do go ahead.
  4. Click Accept, or press Enter with an empty question field. If you do not want it, click Cancel or press Escape.

Accepting carries out all steps as one step in Undo. As long as you did nothing else afterwards, the card also has an Undo button. The proposal then opens again.

You only get a proposal for the plan on the floor plan. A proposal for a circuit shows per field what it is now and what it becomes.

If you ask something new while a proposal is still open, the old one lapses.

Problems

I do not see a microphone in the notes

The microphone is only there with Volter AI and with credit left. Your device or browser must also be able to record audio. You can always type.

Volter is not allowed to use the microphone

You refused the permission, or your device blocks it. Turn on the microphone for Volter in the settings of your device or browser and try again.

Nothing was understood

Speak closer to the microphone and try again.

The recording was not sent

There was no connection, or something went wrong. The recording is not gone. Stay on the screen and click Try again as soon as you have reception again. With Discard you erase it.

Accept is grey

There are three reasons for that:

  • The proposal is for another floor. Open that floor.
  • The plan is locked, or a colleague has the project open.
  • Not a single step can be carried out. Every step says why, for example that the room is not on the plan or that there is no room against the wall.

The assistant puts a symbol in the wrong spot

Click Cancel and say it more precisely: call the room by its name and name the door or the window the symbol has to go next to.

There is no Process into the plan on my note

The button is only there with Volter AI, and not on a note that is already ticked off.

Valid for Volter 1.2.0 · images from 11/15/2026