Placing symbols
Put light points, switches, socket outlets and appliances on your plan, with their quantity and their circuit.
Steps
- In the tools on the left, choose Place symbol, or press R. The Symbols panel opens next to the tools.
- Click a symbol in the panel. Looking for something? Type in Search....
- Click on the plan. The symbol goes under your mouse.
- Click again to place another one. The tool stays active until you press Escape.
You can also drag a symbol from the panel onto the plan, and let go where it should go. That also works from your favourites and from To be placed. If you let go over something that is already there, it lights up and nothing is placed.
With a finger or a pen
On a tablet a tap places the symbol. If you slide with your finger or pen, you move the plan and place nothing. Want a symbol in a precise spot? Drag it from the panel onto the plan.
With a finger you drag sideways out of the panel, or you first hold the symbol down until it lights up. Sliding up and down scrolls the panel.
The panel
The symbols are grouped: Lighting, Switches, Outlets, Appliances, Solar panels and batteries and Other. One group is open at a time.
LED strips, LED panels and fluorescent fixtures have a size or direction of their own. See Lighting.
Without a subscription you can use one symbol per group: light point, switch, socket outlet, household appliance, solar panel and doorbell. The other symbols have a lock.
Favourites
Hold the mouse over a symbol and click the star next to it. It then appears at the top under Favourites, so you do not have to look for it every time. On a tablet the star is always there.
With Reorder you drag the favourites into the order you want, or remove one. Click Done when you are finished. Your favourites follow your account, also on your other devices.
Quantity and circuit while placing
In the row below the tabs, before you click, you choose:
- Type: the symbols you placed last, to switch quickly.
- Quantity: how many devices this one symbol stands for, up to 10. So you place a double socket outlet as one socket outlet with quantity 2. Socket outlets up to 4 are shown stacked, the rest get "x2", "x3" and so on.
- Circuit: the circuit the new device gets right away, or No circuit.
Against the wall
When Wall snap is on, which is the default, a symbol snaps against a wall as soon as you get close. A socket outlet turns along, with its back against the wall.
You find Wall snap in View at the bottom right, under Snap to. Want to put a light point in the middle of a room and it jumps to the wall anyway? Turn Wall snap off for a moment. With Grid snap a symbol snaps to the 20 cm grid.
Changing a symbol
Click a symbol to select it. A bar with the name of the symbol appears where you clicked. In it you find:
- Type: the title of the bar. Switch to another symbol from the same group. The circuit stays.
- Circuit: the circuit. Unassigned takes it off its circuit.
- Quantity.
- Size: draw this one symbol larger or smaller.
- Duplicate: a copy, right next to it.
- Connect with...: see Connecting symbols.
- Delete.
On the computer the bar is small: it holds Circuit, Duplicate and Delete. You find the rest under More, with Type as the first line. An EV charging station, an inverter or a solar panel also has fields of its own, such as the power.
Drag a symbol to move it. With Select you select several by holding Shift.
All symbols larger or smaller
With Symbol size in View at the bottom right you make all symbols on the plan larger or smaller together, from 50 to 200 percent. That applies to the whole project and also to the PDF. The single-line diagram does not change with it.
Placing symbols from the single-line diagram
If you added devices on the single-line diagram, they wait in To be placed in the tools on the left, or press W. That button is only there when something is waiting. Click a device in the list and click on the plan, or drag it from the list onto the plan. Type, quantity and circuit are already set.
Problems
A click places nothing but selects a symbol
You are clicking on or right next to an existing symbol. Click a bit further away.
The first click places nothing
If something was still selected, the first click clears the selection. Click again.
Nothing happens when I click
First pick a symbol in the panel. If it still does not work, check whether the layer of that symbol is hidden or locked. See Using layers.
On my tablet the plan moves instead of placing a symbol
That is right: with a finger or a pen a tap places, and sliding moves the plan. Tap the spot where the symbol should go, or drag it from the panel onto the plan.
My light point jumps to the wall
Wall snap is on, and it applies to every symbol. Turn it off in View at the bottom right for symbols in the middle of a room.
A socket outlet does not snap against the wall
Turn on Wall snap in View at the bottom right. If the Walls, doors, windows layer is hidden, nothing snaps against the wall either, because you cannot see that wall.
I cannot rotate a symbol
Most symbols you do not rotate yourself. A socket outlet turns along with the wall by itself when you put it against it. You can rotate an LED strip, an LED panel and a fluorescent fixture, see Lighting.
I cannot pick a symbol, it has a lock
That symbol is part of the subscription. Without a subscription you can use one symbol per group.
I want to place without a circuit again
Choose No circuit under Circuit in the row below the tabs. Every new device then goes on the plan without a circuit.
Duplicate does not copy the connections
That is right: a copy has no connections. Draw them again with Draw connection.
Valid for Volter 1.0.0 · images from 11/10/2026