Skip to content

The open beta runs until 30 November. From 1 December Volter is paid, and accounts created before 1 December stay free until 31 December. See the prices

Push buttons and home automation

Draw a push button with several buttons, give each button an output or the all off function, and put a roller shutter on two outputs.

How a push button works with home automation

On a home automation module, the module switches the light, not the push button. The push button only sends a signal to an output of the module, such as D.5. In Volter, a push button therefore gets the output it controls, and that output shows as a label on the plan.

The easiest way: connect the push button to the light. It then takes over the output of the light. See Connecting symbols.

A push button with several buttons

A panel with two, four or six buttons is one device. You draw it as one push button:

  1. Select the push button with Select.
  2. In the bar, type under Buttons how many buttons the panel has, up to ten. On the computer, Buttons is under More as long as the push button has one button.
  3. The plan now shows one symbol with, for example, x2, and a label per button. A button without an output shows a question mark.
  4. Connect the push button to the lights it controls. Each connection goes to the next free button, and that button gets the output of the light.

If the push button already controls a light on the same output, no extra button is used. Volter attaches the connection to the button that already has that output.

Setting up buttons

Click Set up buttons in the bar to choose each button separately. On the computer you open More: Set up buttons is right there, with a list per button. Per button you choose:

  • An output: the button controls that output.
  • all off or all on: the button switches everything off or on, without an output.
  • None: the button does nothing yet.

An all off or all on button hangs on the power supply of the home automation module. If another button of the panel is already on an output, Volter takes over that power supply. Otherwise you choose it in the Power supply list next to the button.

Moving the labels and x2

The labels of the buttons sit in a column next to the symbol. Drag the column to a spot where it reads well, for example below the symbol. The whole column moves along while you drag.

The multiplier, such as x3, is dragged separately. It lights up when you hover over it.

A roller shutter on two outputs

A roller shutter motor usually hangs on one output. If your module drives the motor with two relays, one for up and one for down, give it a second output:

  1. Put the motor on the output for up, with Assign circuit or in the bar under Circuit.
  2. Select the motor and click + Second output in the bar. On the computer, that button is under More.
  3. The Down list opens right away. Choose the output for down.

On the plan, both outputs show below the motor, such as D.8 D.9. To remove the second output again, open Down and choose Remove second output at the bottom.

On the single-line diagram

The push buttons sit in the control chain above the power supply of the home automation module. Next to each push button is the output it controls, such as →D.5. Identical push buttons on the same output are drawn together as one symbol with x2 or more. An all off or all on button sits in the same chain, with its function next to it.

A roller shutter on two outputs sits on the branch of both outputs: with ▲ on the output for up, with ▼ on the output for down.

Problems

A button shows a question mark

That button has no output yet. Connect the push button to a light, or choose an output under Set up buttons. If you don't use the button, set Buttons one lower.

Connecting to the push button doesn't work

Every button already controls another output. Set Buttons one higher and connect again.

One click selects all buttons at once

That's right: on the plan the panel is one device. Dragging, copying and deleting take all buttons along. On the single-line diagram you can pick a single button.

My push button has a dashed ring with Assign circuit

At least one button has no output and no function yet. Look for the button with a question mark.

All off doesn't show on the single-line diagram

The button doesn't hang on a power supply yet. Open Set up buttons and choose the power supply in the Power supply list next to the button.

I don't see Down or Second output for my motor

+ Second output only appears for a motor on an output of a home automation module. A motor on an ordinary circuit breaker has one circuit. On the computer, the button is under More. Down only appears once the motor has a second output.

My old push button with a quantity has changed

A push button with a quantity above one from an older project becomes a push button with as many buttons when you open it, all on the same circuit. On the single-line diagram it stays one symbol with x2 or more.

Valid for Volter 1.0.0 · images from 11/10/2026