Lighting
Place an LED strip or LED panel at true size, and give a fluorescent fixture the right number of tubes and the right direction.
LED strip and LED panel
An LED strip or LED panel is a light point with a size of its own. On the plan it is drawn at true size, so you see how long the strip is and how many panels fit in the ceiling.
- An LED strip is a narrow, long rectangle with the cross of a light point at the start, inside the rectangle.
- An LED panel is a rectangle with a cross over the whole area.
Both get a label like every light point, such as T1 or L1.
Placing an LED strip or LED panel
- In the tools on the left, choose Place symbol, or press R.
- In the Lighting group, click LED strip or LED panel.
- Click on the plan. The preview already shows the true size.
You can also drag the button from the list onto the plan. A new LED strip is 1 m long, a new LED panel 30 x 30 cm.
Before you click, R turns the preview a quarter turn. Hold Alt to place it without it snapping against the wall. With a finger you tap the plan and rotate afterwards, in the bar.
Changing the size
Click the strip or the panel. Square handles appear on the plan, as with a door or a window:
- an LED strip has two handles, one at each end. They only change the length.
- an LED panel has four handles, one in the middle of each side. Left and right you pull the length, top and bottom the width.
The other end stays where it is. While you drag, you see the size on the plan.
For an LED panel the bar shows Size, with the common panels: 30 x 30, 60 x 60, 30 x 120 and 60 x 120. You type a size of your own after Dimensions: Length, and for a panel also Width, in cm.
Rotating
You rotate an LED strip or LED panel in the bar:
- Rotate turns it a quarter turn around its middle.
- You type a free angle after Dimensions, under Rotation.
On the single-line diagram
An LED strip or LED panel is an ordinary light point of its circuit:
- On the single-line diagram it is shown as a light point, with its label.
- The AREI check counts it as one light point.
- In the bill of materials it is listed as an LED strip or LED panel, with its size.
If you open the project in an older version of Volter, you see an ordinary light point. The size is kept and comes back in the new version.
A fluorescent fixture
In the list the fluorescent fixture is called Fluorescent fixture, in the Lighting group. On the plan it is one line per tube, with a stroke at both ends.
Click the fixture. In the bar you choose how many tubes it has, from 1 tube to 4 tubes. A new fixture has one. The single-line diagram shows the same number of tubes.
Rotating a fluorescent fixture
You rotate a fluorescent fixture in the bar:
- Rotate turns it a quarter turn.
- You type a free angle under More, under Rotation.
- While placing, R turns the preview.
If you open the project in an older version of Volter, you see a fixture with one tube.
Problems
I cannot find an LED strip or LED panel
They are in the Lighting group of Place symbol. Or type "led" in Search....
My LED strip points the wrong way
Click the strip and choose Rotate in the bar until it lies right. While placing, R turns the preview beforehand.
I cannot change the width of my LED strip
That is right: an LED strip only has a length. Want a wide area? Place an LED panel.
I want a panel size other than 30 x 30
Choose 60 x 60, 30 x 120 or 60 x 120 under Size in the bar. You type another size after Dimensions, or you drag the handles of the panel.
My LED panels show as an ordinary light point on the single-line diagram
That is how it should be. On the single-line diagram an LED strip or LED panel is a light point of its circuit. The size is in the bill of materials.
My colleague sees an ordinary light point instead of my LED strip
Their Volter is older. There an LED strip or LED panel shows as an ordinary light point, but the size is not lost. After an update they see the strip at true size again.
I cannot find a fluorescent fixture
It is called Fluorescent fixture, in the Lighting group.
How do I draw a fixture with two tubes?
Click the fixture and choose 2 tubes in the bar. The plan and the single-line diagram then show two tubes.
My fluorescent fixture is horizontal and should be vertical
Click the fixture and choose Rotate in the bar: a quarter turn. You type a slanted position under More, under Rotation.
Valid for Volter 1.0.0 · images from 11/10/2026