Skip to content

The open beta runs until 30 November. From 1 December Volter is paid, and accounts created before 1 December stay free until 31 December. See the prices

Drawing walls and rooms

Draw the walls of the house, curved ones too, assign the rooms and work with several floors.

Drawing a wall

  1. In the tools on the left, click Build. The Build menu opens next to the button, with Draw wall selected. Or press E or S: that picks the wall straight away, without opening the menu.
  2. Press the mouse where the wall starts, drag to the end and let go.
  3. For the next wall, start dragging again at the end of the previous one. The start point snaps there.

Every drag is one wall. A plain click draws nothing: it only selects the wall underneath. While you drag you see the length, and a wall shorter than 20 cm is not created.

Snapping and angles

While you drag, the point snaps:

  1. to the end of an existing wall, when you are close to it,
  2. otherwise to an existing wall itself. Your new wall then joins it, like a T,
  3. otherwise to the grid, when Grid snap is on in View at the bottom right.

While you draw, a wall runs in steps of 15 degrees: horizontally, vertically or diagonally at 15, 30, 45, 60 or 75 degrees. You enter any other angle afterwards at the joint, see Entering an angle. Or let the wall end on an existing corner or an existing wall.

To draw an inner wall, start in the middle of an existing wall and end on the wall opposite. It joins at both ends like a T and splits the space in two. Then, with Select or after pressing Escape, drag a corner away. The walls that meet there follow at any angle.

Exterior and interior walls

Choose the thickness before you draw. As long as Draw wall is chosen, the row below the tabs shows under Thickness:

  • Exterior wall: 30 cm.
  • Interior wall: 15 cm.
  • Other: type the thickness in cm yourself.

Volter remembers your last choice. So draw the facade first with Exterior wall, then choose Interior wall and draw the walls inside.

Walls from an older project stay 20 cm thick. You give them another thickness with Thickness in the bar of the wall, see Changing a wall.

Entering an angle

Click a joint where two walls meet with Select. The Joint bar appears at the joint, with the Angle between the two walls. On the plan, a lock marks the wall that stays, and a curved arrow marks the end of the wall that turns. The swap button next to the angle switches the two.

  • Type an angle and press Enter.
  • Or use the arrow keys in the field: one degree per step, fifteen with Shift. The dashed line shows the new position, Enter applies it.
  • Or drag the dot at the end of the wall that turns. The angle snaps every 15 degrees, with Alt any angle works.

If another wall hangs at that end, it keeps its direction. The wall that turns becomes as long as needed to connect to it. Doors, windows and rooms move along.

At a T or a crossing, you choose in the bar which wall stays and which turns. A wall that runs through the joint always stays.

Changing a wall

Click a wall with Select, or simply with Draw wall: a short click selects the wall. A bar appears where you clicked, with:

  • Length: type a new length in cm and press Enter. Walls attached to it move along.
  • Thickness: choose Exterior wall, Interior wall or Other with your own thickness in cm. If other walls join this wall, only the piece you clicked gets the new thickness: Volter cuts the wall there.
  • Dimensions: the eye shows or hides the dimension line of this wall.
  • Bend: see A curved wall.
  • Delete: the wall goes away, with the doors and windows in it.

Drag a corner to move all the walls that meet there. Drag a whole wall to shift it. The walls next to it stretch along, and the devices against the wall move with it. With Draw wall you select the wall first: dragging over a wall that is not selected yet draws a new wall.

Right-click a wall, or hold it down on a tablet, and choose Split wall here to turn it into two walls. To remove a corner between two walls in one line, use Remove joint.

A curved wall

Select a wall and click Bend in the bar. Or right-click the wall and choose Bend. The piece you clicked bends outwards. If other walls join it, only the piece between the two nearest joints bends.

  • Drag the grip in the middle of the arc to make it deeper or flatter. Drag the grip across the wall and the arc bends the other way.
  • Or type in Curve how many cm the middle of the arc lies from the straight line.
  • Length shows the length along the arc. You cannot type it here.
  • Straighten in the bar, or in the right-click menu, makes the wall straight again.

Socket outlets and other devices against the wall slide and turn with the arc. A room with a curved wall follows the arc, and so does its area.

You place, drag and resize doors and windows as on a straight wall. A window follows the arc. A door stands straight in its opening, with both sides on the arc.

You cannot split a curved wall. A new wall only joins it at its ends, not in the middle of the arc.

Assigning rooms

Rooms do not appear by themselves: you assign them. Volter uses them to count devices per room in the bill of materials and for the AREI check, for example for a bathroom or a damp room.

A garden, terrace or driveway is not a room. You draw those with Outdoor, see Garden and terrace.

In the Build menu, choose Assign room, or press G. At the bottom of the menu, under Method, you choose how: Auto-detect, Rectangle or Freeform. The menu then closes and the tool stays on, so you can assign one room after another.

A new room is called "Room" with a number. Double-click the name to rename it. The area is shown below it.

Auto-detect

Move the mouse into a space enclosed by walls. The pointer becomes a magic wand and the space lights up. Click, and it becomes a room.

A gap of up to 10 cm between two walls is no problem: Volter closes it for you. Walls that cross each other, or a loose piece of wall in the room, do not stop the detection either.

The room follows the walls. If you drag a wall or a corner, the room changes with it, and so does the area.

If the space is not closed, it does not light up. Red dots then show the loose ends of the walls, with the message "This room is not closed. Draw it as a freeform." Join the walls there, or draw the room as a Freeform.

Rectangle

Drag a rectangle from one corner of the room to the other. This also works where the walls do not close, such as a carport or an open kitchen, and even without walls.

A rectangle does not follow the walls. If you move a wall later, the room stays where you drew it.

Freeform

For a room that is not rectangular and not enclosed by walls either, such as an open kitchen with a slanted side.

  1. Choose Freeform at the bottom of the menu.
  2. Click the corners of the room one by one. A corner snaps to a nearby wall corner.
  3. Close the room by clicking the first point, with a double-click or with Enter.

Backspace removes a wrong corner. Escape clears all the corners you clicked.

A freeform does not follow the walls either.

Changing a room

Click the name of the room to select it. Clicking inside the room itself does not work. In the bar that appears:

  • Show or hide the Area on the plan.
  • Bath or shower: every circuit to this room must then sit behind a 30 mA RCD. Put a bath or shower from Furnishing in the room and Volter ticks this for you.
  • Damp room: for a basement, garage, laundry room, covered terrace or outdoors. Socket outlets there must be splash-proof.
  • Delete.

The i next to Bath or shower and Damp room shows what each tick box means, also on a tablet.

A room you drew yourself, with Rectangle or Freeform, gets grips on its corners when you select it. Drag a corner to another place. An auto-detected room has no grips: it follows the walls.

Dimensions

The dimension lines of the walls are on the Dimensions layer. In a new project that layer is off. Turn it on in Layers. Whether the dimensions are visible belongs to the project: your teammates see the same, and that is how it goes into the PDF.

When you are zoomed far out, Volter hides the dimension lines on screen. They are still in the PDF.

Floors

The row below the tabs shows Floor with the floor you are working on. The first one is called "Ground floor". In the menu:

  • click a floor to go there,
  • Add floor adds a floor at the top,
  • per floor: Rename, Duplicate, Move up, Move down and Delete.

Duplicate copies the walls and rooms, not the devices. Useful for a floor with the same outer walls.

Problems

A click does not draw a wall

You draw a wall by dragging, not by clicking. Press, drag and let go.

Assign room does not find my room

The space is not closed. Volter closes a gap of up to 10 cm by itself. If the opening is larger, red dots show where the walls do not join. Let the walls join there, or draw the room with Freeform or Rectangle.

I cannot draw a diagonal wall at another angle

While you draw, a wall runs in steps of 15 degrees. Draw the wall first, then enter the angle at the joint: see Entering an angle.

My room has disappeared

An automatically assigned room disappears when you delete or move a wall so the space is no longer closed. Undo brings it back.

I cannot drag a corner of my room

Only a room you drew yourself with Rectangle or Freeform has grips on its corners. An auto-detected room follows the walls: drag the wall or the corner instead.

I cannot split a curved wall

That is not possible. Click Straighten, split the wall, then bend the piece you want.

A new wall does not join my curved wall

A wall only joins the ends of a curved wall, not the middle of the arc. Let the new wall start or end there.

I cannot select my room

Click the name or the area of the room, not just anywhere inside it.

I see no dimensions

The Dimensions layer is off, which is the default in a new project. Turn it on in Layers. Or you are zoomed out too far.

A wall does not snap to the grid

Turn on Grid snap in View at the bottom right. The grid has steps of 20 cm.

The tool draws nothing and says "is hidden"

The Walls, doors, windows layer is hidden or locked. See Using layers.

I cannot add a floor

Several floors are part of the full version. Without a subscription, Add floor opens a window to upgrade.

Valid for Volter 1.0.0 · images from 11/10/2026