Skip to content

The open beta runs until 30 November. From 1 December Volter is paid, and accounts created before 1 December stay free until 31 December. See the prices

Stairs and furniture

Put stairs, a kitchen, a bathroom and furniture on your plan, so your client recognises the house.

Why furniture

Furniture and stairs make the plan easy to read: an installer, an inspector or your client sees right away where the kitchen and the bathroom are. They do not count in the bill of materials, the circuits or the single-line diagram.

One exception: put a bath or shower in a room and Volter ticks Bath or shower for that room. That does count for the AREI check.

Opening Furnishing

In the tools on the left, click Furnishing, or press J. The Furnishing panel opens next to the tools, with the stairs at the top and the furniture by group below. The panel stays open, so you can place several pieces one after the other.

Placing a piece of furniture

  1. Click a piece of furniture in the panel.
  2. Press R to turn it a quarter turn, as often as needed.
  3. Click on the plan. The centre of the piece goes under your mouse.

You can also drag a piece of furniture from the panel onto the plan, and let go where it should go. If you let go over something that is already there, it lights up and nothing is placed.

A piece with its back against a wall snaps there when Wall snap is on in View at the bottom right. Hold Alt to place it without snapping.

A worktop can be as long as you want: select it and drag the handle on each side up to the wall. A hob or sink you put on a worktop goes into the worktop.

With a finger or a pen

On a tablet a tap places the furniture or the stairs. If you slide with your finger or pen, you move the plan and place nothing. You rotate after placing, with Rotate in the bar.

Want a piece of furniture in a precise spot? Drag it from the panel onto the plan. With a finger you drag sideways out of the panel, or you first hold the tile down until it lights up. Sliding up and down scrolls the panel.

Which furniture there is

  • Sleeping: double bed, single bed, cabinet.
  • Living: sofa, corner sofa, armchair, table, round table, chair.
  • Kitchen: worktop, hob, sink.
  • Bathroom: bath, shower, washbasin, double washbasin, toilet.
  • Technical: AC outdoor unit, AC wall unit, AC ceiling cassette, lift.

Placing stairs

At the top of the panel, choose Straight, Quarter-turn or Spiral stairs and click on the plan. Stairs do not have to be against a wall.

Changing furniture and stairs

Select a piece of furniture or stairs. Handles appear on the plan to change the size, and one handle to rotate freely. A bar appears where you clicked, with:

  • Rotate: a quarter turn to the right.
  • Dimensions: type the sizes in cm, and for furniture also the Rotation in degrees.
  • Mirror: for a corner sofa, sink, bath and AC outdoor unit.
  • Duplicate: a copy of the piece, right next to it.
  • For stairs: Turn direction for quarter-turn or spiral stairs, and Sweep for spiral stairs.

Drag a piece of furniture or stairs to move it. While you drag, it lines up with the edges of other furniture. You then see a guide line. Turn off Guides in View at the bottom right, or hold Alt, to drag without lining up.

Problems

A click does not place furniture but clears the selection

If something was still selected, the first click clears the selection. Click again to place.

The furniture does not snap against the wall

First turn it with R so its back faces the wall, and get close enough to the wall. Also check that Wall snap is on in View at the bottom right. A piece that is already on the plan no longer snaps against a wall when you drag it.

My room is set to Bath or shower, but the bath is gone

Volter ticks Bath or shower, but does not untick it by itself. Select the room and untick it yourself.

I do not see the handles

You have selected more than one piece, or the Furniture, stairs layer is locked or hidden. See Using layers.

R does something else

With Furnishing, R turns the piece you are about to place. With another tool, R picks Place symbol.

On my tablet the plan moves instead of placing furniture

That is right: with a finger or a pen a tap places, and sliding moves the plan. Tap the spot where the piece should go, or drag it from the panel onto the plan.

I cannot find the sizes of my furniture

Click the piece and choose Dimensions in the bar. There you type the sizes and the rotation.

I do not want the furniture in the PDF

Untick Furniture, stairs under Layers on the Export tab. See Export a PDF.

Valid for Volter 1.0.0 · images from 11/10/2026