Connecting symbols
Connect a switch to its light points, so Volter puts them on the same circuit and the same branch of the single-line diagram.
Why connect
A connection says which devices belong together, such as a switch and the light points it controls. Volter uses that in three places:
- Circuits: connected devices share the same circuit.
- Single-line diagram: connected devices sit on one branch, with the switches first.
- References: all devices of one branch get the same code on the plan, such as A1.
Steps
- In the tools on the left, choose Draw connection, or press T. This only works on the floor plan.
- Click the first device. It gets a ring.
- Click the second device. The connection is made.
Dragging from one device to the other works too. On a tablet, tapping is usually easier.
To cancel, click next to a device or press Escape. Escape also takes you back to the Select tool.
A circuit with several devices
A connection always runs between two devices. For a switch with three light points you draw three connections, or a chain: switch to light point, light point to light point. For the single-line diagram only the members of the group count, not the order in which you draw.
For a two-way circuit you connect both two-way switches, any intermediate switches and the light points. Volter puts the switches in the order two-way, intermediate, two-way. If the group does not have exactly two two-way switches, the AREI check gives a warning.
Line, weight and curve
While you draw, you choose in the row below the tabs:
- Line: Solid, Dashed, Dotted or Dash-dot.
- Weight: from Very thin to Very thick.
- Curve: Straight, Slightly curved or Curved.
The style has no electrical meaning. You choose it yourself, for example a different line for a control wire. The colour always follows the circuit.
You set your default style in Settings, in your account menu at the top right, under Preferences and Connections. What you change in the row stays until you click Reset to saved preferences.
Changing a connection
Click the line to select it. In the bar that appears you change Line and Weight, also for several connections at once.
To bend a line, drag the dot in the middle. Double-click that dot to make the line straight again.
When you move a device, the connection moves with it.
Deleting a connection
There are three ways:
- Select the line and press Delete, or click Delete.
- Select a device. Under More in the bar you find the Connections list, with a cross per connection.
- Right-click a device, or hold it down on a tablet, and choose Disconnect from ... or Disconnect all.
When you delete a device, its connections disappear with it.
Connecting to another floor
A switch downstairs that controls a light point upstairs:
- Select the first device and choose Connect with... in the bar. On the computer it is under More. With the right mouse button you choose Connect to other floor....
- Go to the other floor.
- Click the second device.
As long as Volter is waiting for the second device, a message with Cancel is shown on the plan.
On both floors a dotted line appears, leading to a label with the device and the floor on the other side. Click that label to jump to the other floor.
Problems
Symbols belong to different circuits
Both devices, or their groups, are already on different circuits. First take one of them off its circuit, then connect again.
A device changed circuit when I connected it
Connected devices share their circuit. If one device had no circuit yet, it takes over the circuit of the other.
I cannot connect the distribution board, a data or a coax outlet
These devices do not need to be on the single-line diagram, so they get no connection. A click on them does nothing.
A right-click does not cancel drawing
That is right: a right-click opens the menu of the device. Cancel with Escape, or by clicking next to a device.
Nothing happens when I connect two devices
They are already connected to each other. A second connection between the same pair is not created.
I get a warning about the two-way circuit
The group has two-way switches or intermediate switches, but not exactly two two-way switches. While you are still drawing, that is normal. Connect both two-way switches to the group and the warning disappears.
I cannot click a line, or it is gone
The Connections layer is hidden or locked, or the layer of one of the two devices is hidden. See Using layers.
I cannot find Draw connection on the single-line diagram
You connect on the floor plan. The single-line diagram follows by itself.
I cannot find Connect with... in the bar
On the computer, Connect with... is under More. It only appears when you select exactly one device.
Valid for Volter 1.0.0 · images from 11/10/2026